Charcoal-Ashs-art - 4/3/17 "Of Charcoal and Ashes" by Unnr in elska á Fjárfella. NOTE: See also the files: charcoal-msg, Lye-Soap-art, Mkng-Charcoal-art, Pyrography-art, soapmaking-msg, wood-msg, soap-msg, Hist-of-Soap-art. ************************************************************************ NOTICE - This article was added to this set of files, called Stefan's Florilegium, with the permission of the author. These files are available on the Internet at: http://www.florilegium.org Copyright to the contents of this file remains with the author or translator. While the author will likely give permission for this work to be reprinted in SCA type publications, please check with the author first or check for any permissions granted at the end of this file. Thank you, Mark S. Harris...AKA:..Stefan li Rous stefan at florilegium.org ************************************************************************ You can find more work by this author on her blog at: http://bookeofsecretes.blogspot.com Of Charcoal and Ashes by Elska á Fjárfella Charcoal is formed by the incomplete burn, or combustion, of wood. Made of mostly cellulose, wood does not burn immediately, first it releases steam and turns from white to black; it chars, thus becoming charcoal. When charcoal burns in contact with air, its carbon combines with oxygen to form the gas carbon dioxide (and lots of heat). The white ash leftover from burning charcoal is what remains of the small amount of non-flammable minerals which were present in the wood from the start. The charring of cellulose: Cellulose (CH2O) in combustion forms Carbon (C) and water (H2O). The combustion of charcoal: Carbon (C) heated with Oxygen (O2) forms Carbon Dioxide (CO2). As different varieties of wood grown on different soils have different compositions, ash will also have a variable composition, something to keep in mind when using ashes to leach lye. The part of ash that can dissolve in water and be leached out is called potash, or potassium carbonate. But potash is not the only soluble component, and depending on soil conditions, sodium carbonate might also be present. Along the seashore, and especially when burning marine plants there may be more sodium carbonate than potassium carbonate present and this product is called soda ash. Sodium sulfates and potassium sulfates can also be present, and for the proper making of lye for soap, these contaminants should to be removed as they can interfere with the saponification process. Potash and soda ash can be crystallized by evaporating water from the leached alkaline solution. As potassium carbonate (147g/100ml) is highly soluble compared to sodium sulfate (11g/100ml), potassium sulfate (12g/100ml) and sodium carbonates (22g/100ml) the contaminants will crystallize out of solution first. If the alkaline solution is left alone for a while the less soluble compounds crystallize out and will sink to the bottom while the potassium carbonate would stay in solution as long as possible. Pour off this solution to leave these crystals behind and the lye made will have less contaminants. When wood is burned without the presence of oxygen (anaerobic) it turns black as the water is evaporated out, leaving charcoal behind. If access to air is limited and heat is removed, the charcoal will become stable and available for future use. Charcoal takes up less space and is able reach a higher temperature with the addition of extra air (bellows) than a pile of wood, which makes it ideal for use in a smithy’s furnace. To make proper charcoal an anaerobic burn is necessary, and in history people have found different ways of doing so, mostly by either digging a hole in hillsides or covering wood with a burn resistant material (like a metal kettle) while building a large fire right over it. A side note: The burning of marine plants creates sodium carbonate rich ashes. At the sea shore where barilla is available in abundance making soda ash is not much different from making potash. But it’s a challenge for the small scale experimental soap maker as the goal is pure barilla (or seaweed, or kelp) ashes, without potassium carbonate (land based plants) contamination. As marine plants don’t easily burn on their own, unlike wood, a way around this is to first make, for instance seaweed charcoal, which does burn, and then burn it to ashes, with plenty of air for complete combustion to create fine white ashes for the lye leaching vat. ------ Copyright 2017 by Susan Verberg. . Permission is granted for republication in SCA-related publications, provided the author is credited. Addresses change, but a reasonable attempt should be made to ensure that the author is notified of the publication and if possible receives a copy. If this article is reprinted in a publication, please place a notice in the publication that you found this article in the Florilegium. I would also appreciate an email to myself, so that I can track which articles are being reprinted. Thanks. -Stefan. Edited by Mark S. Harris Charcoal-Ashs-art 2 of 2